[jedrekx]

Znalazłem kilka kodowań do D4 poprzez VCDS, sam też kilka zrobiłem u mojego ojca. Poniżej wrzucam:

Disable After-wipe of windscreen wipers
[09 – Cent. Elect.] [Coding - 07] -> Byte 1
Bit 3 - Remove check mark (1 = active)
________________________________________
Disable amber corner lights
[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 10
Submodule 0
Bit 3 - Set to 0 to disable amber side markers (U.S. vehicles)
________________________________________
Disable Key warning
[46 – Central Conv.] [Coding - 07] -> Long Coding Helper -> Byte 9
Bit 7 set to 0 (Uncheck)
________________________________________
Disable "Lights are on" Warning
[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 5
Bit 3 - Set to 0 to disable "lights are on" warning when you open the door.
________________________________________
Disable NAV & Phone warning messages while entering data at speed
[5F - Information Electr.] -> Adaptation -> Set channel 2 & 3 to 250
________________________________________
Disable Seatbelt Chime
[17 - Instruments] [Coding - 07] -> Long Coding Helper -> Byte 0
Bit 2-4 – Seat Belt Warning inactive
________________________________________
Adjust Date display
[17 – Instruments]
[Coding - 07] -> Long Code Helper ->
Byte 7 – Use dropdown to select date format
________________________________________
Upshift Display
[17 – Instruments]
[Adaption - 10] -> Upshift Display in center panel ->
Use dropdown to activate/deactivate
(untested)
________________________________________
Enable Adaptive brake lights
[46 - Comfort System] [Coding - 07] -> Long Coding Helper -> Byte 8
Bit 0 – Emergency Brake Flashing via Turn Lights active (1 = active)
Bit 1 – Emergency Brake Flashing via Brake Lights active (1 = active)
__________________________________________

Enable Double Disarm Beep
[46 - Central Conv.] [Adaptation - 10] -> Channel 63
Add 4
________________________________________
Enable/Disable Auto Locking
[46 – Central Conv.]
[Coding - 07] -> Long Code Helper ->
Byte 5 – 0=off/1=on
Bit 4 – Auto lock
Bit 5 – Auto Unlock
________________________________________
Enable DRL to include the following:
[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 2
Bit 1 = DRL with Front Side markers
Bit 2 = DRL with High Beams
Bit 3 = DRL with Fog lights
Bit 4 = DRL with LEDs
Bit 6 = DRL with Side markers
Bit 7 = DRL with Tail lights
________________________________________
Enable Euro parking lights that turn on signal at night
[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 9
Bit 0 - Set to 1
________________________________________
Enable fog lamp to come on for the same side as that turn signal
[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 4
Bit 0 - Check the box or change :Bit 0 set to 1
________________________________________
Enable Front Turn Signals as Parking lights
[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 10
Bit 0- Check the box or change :Bit 0 to 1
________________________________________
Enable Gauge Test/Needle Sweep
[17 - Instruments] [Coding - 07] -> Long Coding Helper -> Byte 1
Bit 0 - Check the box for "Gauge Test/Needle Sweep active"
________________________________________
Enable Hidden menu in MMI
[5F - Information Electr.]
[Adaptation - 10] -> Channel 6
change 0 to 1
Use this hidden menu at your own risk.
Caution: Keep away from the "Bootloader", if it appears as an option
________________________________________
Enable Import CDs to MMI's HD
[Hidden menu]
Main/Diagnose/Settings
Import Media
Set to 4 of 4 "Copy/Ripping"
Note: CD must be inserted in player below the mmi, not the changer in the glovebox to be able to rip it.
________________________________________
Enable Independent Fogs control with high beams
[09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 4
Bit 1 – (Front) Uncheck the box or change :Bit 1 to 0
Bit 2 – (Rear) Uncheck the box or change :Bit 2 to ______________________________________
Enable Remote Operation Windows and Sunroof
[46 - Cent. Conv.] [Coding - 07] -> [Long Coding Helper] Byte 2
Bit 2 - Set to 1
________________________________________________
Enable Release Parking Brake without putting foot on Brake
[53 - Parking Brake][Security Access - 16] (Enter code presented by program)
[Adaptation - 10] -> Channel 4 Set to 0
________________________________________
Enable Release Parking Brake without putting seatbelt
[53 - Parking Brake][Security Access - 16] (Enter code presented by program)
[Adaptation - 10] -> Channel 7 Set to 0
________________________________________
Enable Reverse mirror tilt
[52 Door Elect, Pass.] -> [Coding - 07] -> [Long Coding Helper] -> Byte 4
Bit 4 and Bit 2 set to 1
________________________________________
Enable VIM on MMI
[5F - Information Electr.] [Advanced ID - 1A] Note 1st Serial number
[Security Access] Enter Digits 6, 13, 10, 14, 11 of the 1st Serial number
[Adaptation - 10] -> Channel 48
Set to 255
Reset MMI
________________________________________
Set ADS to specific preset Comfort, Auto, Dynamic or Individual
[09 – Cent. Elect.][Security Access - 16](VCDS will have popup telling you the access code, mine was 20113)
[Adaptation - 10] -> Channel 63
Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual
[Adaptation - 10] -> Channel 64
Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual
[Adaptation - 10] -> Channel 65
Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual
[Adaptation - 10] -> Channel 66
Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual
*Note all four channels needs to be set to the same value. (Uncomfirmed)

________________________________________
Set Headlight washer – Duration (values in milliseconds)
[09 – Cent. Elect.]
[Security Access - 16] [Adaptation - 10] -> Channel 6
change to e.g. 500
________________________________________
Set Headlight washer – Activation Delay
[09 – Cent. Elect.]
[Security Access - 16] [Adaptation - 10] -> Channel 25
change to e.g. 3000
________________________________________
Set Headlight washer – Delay (How many times you can activate the regular washers without activating the headlight washers)
[09 – Cent. Elect.]
[Security Access - 16] [Adaptation - 10] -> Channel 25
change to e.g. 3000
________________________________________
Set Coming Home Time– Duration
[09 – Cent. Elect.]
[Security Access - 16] [Adaptation - 10] -> Channel 43
change to e.g. 30
________________________________________
Activate/Deactivate Leaving Home Function
[09 – Cent. Elect.]
[Security Access - 16] [Adaptation - 10] -> Channel 46
change to 0=off / 1=on
________________________________________
Coming Home – Ambient Light Threshold for activation
[09 – Cent. Elect.]
[Security Access - 16] [Adaptation - 10] -> Channel 37
change from 0-7
________________________________________
Enable/Disable Coming Home and Leaving Home Function
[09 – Cent. Elect.]
[Coding - 07] -> Long Code Helper ->
Byte 6 – 0=off/1=on
Bit 1 – Coming Home
Bit 2 – Leaving Home
________________________________________
Enable/Disable Parking Lights
[09 – Cent. Elect.]
[Coding - 07] -> Long Code Helper ->
Byte 9 – 0=off/1=on
Bit 0 – Parking Light Function
___________________________________________
Adjust LED brightness
[09 – Cent. Elect.] [Security Access - 16] (enter security code. One of the default codes is- 20113)
[Adaptation - 10] -> Channel 3
Set between 5 and 100

Powodzenia!

[ernesto]

Popraw proszę tytuł tego wątku zgodnie z regulaminem. Zastosuj w nim odpowiednie tagi. W przypadku nie poprawienia, zostanie on usunięty